This can cause confusion for the end user.
POOL CONTROL PANEL PRO
This can happen if the pro thought a program didn’t go through and re-entered it. They might, for instance, set more than one pump schedule without realizing it. Sometimes homeowners or less-experienced pool and spa professionals accidentally program redundant or conflicting functions into the controller. If the water moves too slowly, copper heat exchangers can melt or other damage occur.
Generally speaking, heaters need at least 40 gpm to protect it from overheating. For instance, a pump may be scheduled to run at a lower speed - say, 20 or 30 gallons per minute - at a time when the heater may turn on. Relying on default settings can result in system problems. The set point, alarms and feed event timers likely will need adjustment to meet the demands of the specific vessels - particularly when it comes to chemical levels. However, the scheduling will probably be wrong because it isn’t customized to the homeowner’s pool or spa. Many controllers come with default programming to operate primary functions. simplified the job by eliminating unnecessary wires and high-voltage valve actuators. For instance, try to avoid putting it on top of a wall or other location where a gardener trimming bushes might inadvertently cut it.Īfter: Pools by Ben in Santa Clarita, Calif. In such cases, consider mounting the units on poles, fences or other nearby structures.If there is no good, obstacle-light location, units with longer cables can be placed in the attic, since signals transmit more easily through wood framing and shingles.Īlso think in terms of the antenna’s exposure where it’s placed. This includes stucco walls, since the wire mesh underneath will act as a ground plane and send incoming signals to ground rather than the receiving load center. Keep the transceiver away from metallic elements, which also can cause interference. This eases the signal’s path and minimizes the possibility of interference. Also try finding a place with the fewest solid obstacles possible between the antenna and modem.
But reception can be hindered by this practice, as the high voltage inside the automation box can cause interference and degrade the signal.Īdding to the challenge: The Federal Communications Commission only allows controllers to emit approximately ¼ watt of power, making it crucial that professionals strategically place the transceiver.įor the best reception, place the unit at least 10 feet from the load center. They do this to create the cleanest-looking installation or in the belief that having the two components right next to each other will guarantee the best signal. Some installers mistakenly will put them directly on or inside the controller housing, or load center. The antenna, also known as a transceiver, should be placed to provide the best signal possible. Carefully locate the antennaĪntennae send signals from the home’s internet connection, allowing the user to control via a smartphone, tablet or computer. This will help you program the unit to meet the needs of the owner and circulation system. Take it out of the box and look at it.Also, learn about the pool’s and/or spa’s hydraulics and use ahead of time. But is it equipped to read the air temperature? If not, check with your customers to see if they want that capability.Īdditionally, if you’re installing a controller for the first time, or are new to a particular model, do some legwork before actually going to the site and installing it. For instance, it probably will come with a water-temperature sensor. Make sure the controller has all of the needed sensors.
This safety feature can detect when an auto cover is closed and keep the waterfeature pump off.Add a few spare relays for functions that could be added in the future. Landscape lighting often goes ignored, as does the external input for an automatic pool cover. Explore those options before deciding how many functions the controller should accommodate. Specifically, some professionals don’t program controllers with as many functions as possible.ĭon’t forget: Some devices can control things outside the pool, such as landscape lighting and irrigation. One of the biggest selling points for automatic controls can be, ironically, one of its most neglected, experts say. The following tips should go even further to help ensure success when replacing or servicing these units. Over the last few years, manufacturers have made considerable strides to simplify the units, so they’re more intuitive for professionals and users alike, largely through the integration of the internet and mobile devices. When working on controllers, you’re dealing with electronic components, which require a delicate hand.Īutomated controllers are the most sophisticated pieces of equipment found in the pool and spa industry, hands down.
0 kommentar(er)
